AlexAngely, ха, кто сказал, что нельзя

сек...
Добавлено через 27 минут 3 секунды:
ED
AlexAngely, установите разблокированный биос для ваших ноутов, появится громадное количество доступных опций от
СЮДА. запускаем файл InsydeFlashx64.exe, ждем завершения установки и перезагрузки. Вентиляторы системы включатся на макс - это норм)
AlexAngely, попробуй установить в биос х42,42,42,42, pripalne 900, vid - 0, Long/Short duration PWR на макс и прогони марк еще раз) Не забудь подставить тыл ноута на книги/диски для дополнительного притока воздуха!
ED, посмотри есть ли в этом биос настройка автоматического переключения видео! сколько выдает времени от работы аккумулятора в режиме спокойствия? если около 4 часов, значит просто оптимус задействована
Добавлено через 6 минут 49 секунд:
AlexAngely, прошить биос твоих карточек:
- спойлер
- Windows 7 x64 bit only
nvflash 5.100.0.1 only works within windows itself will not work in msdos bootup
(1) download nvflash v5.10
boot in win 7 and just before you load the windows logo press F8 to get into the startup screen.
In there you must select disable driver signature and then it should boot in windows
(2) load command prompt by start / all programs / accessories / command prompt
(3) extract the nvflash file into the c drive folder name nvflash - you should have nvflash.exe nvflash32.sys and nvflash64.sys
(3a) also in that folder nvflash on the c drive you should have your modified bios/Original Vbios (that you wish to flash) for eg called **.rom
(4) back in command prompt direct yourself to that nvflash folder by cd.. cd.. then cd nvflash
(cd c:; cd nvflash)
When you do a dir listing you should see all your files there ready to go.
(5) As i was running DELL SLI 580M in my m18x they are maked as number 0 and number 1
(6) BACKUP YOUR ORIGINAL BIOS FIRST
i did it like this for both in command prompt type
nvflash -b backup0.rom (for the first card)
nvflash -b backup1.rom (for the second card)
(7) to flash just type the following
In case - Error: Firmware image filename must have a *.rom or *.nvr extension
just use --index=o(1) instead of i0(1)
for the first card
nvflash -i0 -5 -6 ***.rom (*** means your file name you want to flash.rom)
A few messeges will come up are you sure etc type y and y all done
for the second card type
nvflash -i1 -5 -6 ***.rom
A few messeges will come up are you sure etc type y and y all done
reboot uninstall drivers reboot install drivers again and thats it.
Биос с 0.92в на карту и частотами 800/1800! оптимальные) Сорри, что на англ, писал на пару с одним товарищем для забугорного форума, будут вопросы - обращайся!
NvFlash ТУТ. После прошивки обязательно перезагрузи комп и проверь в ГПУ-З вольтаж при нагрузке, если не изменился - переустанови драйвера.
Добавлено через 3 часа 35 минут 7 секунд:
Товарищи, ветку почистил! Стараемся держать как можно чище. С этого момента обсуждения только по теме
